Mod-01 Lec-15 Lecture-15-The Shock Tube: Propagating Normal Shock and its reflection from end wall
0:11
그럼 충격관을 조금 더 살펴보겠습니다.
So we shall continue with the Shock Tube little bit more, ok.
0:18
지난 강의에서 말했듯이
So, like we said that
0:24
말입니다.
is the last lecture.
0:30
이런 충격관이 있습니다.
So, we have this shock
0:35
충격관입니다. 여기에는
tube. So, we had a
0:38
파열시키는 격막이 있었습니다. 다시 그려보면
diaphragm which we break. So, let us do this
0:44
이렇습니다. 이것이 격막이고,
right back. So, this was our diaphragm, so
0:49
이것이 충격관입니다. 여기는 영역
this is our shock tube, so this was a region
0:53
4이고, 여기는 영역 1입니다. 이것이 우리가
4 and this is a region 1, this is what we
0:57
말한 내용과 그에 해당하는 값입니다. 그러면
said and the corresponding values. So, then we
1:02
이 격막을 파열시킵니다. 격막을 파열시키면
break this diaphragm. We break this diaphragm
1:06
그 경우에는 다음과 같은 현상이 생깁니다.
and what we have in that case is that; we
1:11
비슷한 접촉면을 가지고 있다
have a contact surface which is similar to
1:17
미끄럼면과 비슷합니다. 격막을 파열시키면 본질적으로
a slip surface. So, what we essentially have when we break
1:27
격막이 파열되면서
the diaphragm is there
1:32
정상 충격파입니다
is a normal shock
1:37
이는 내부로 이동하기 시작합니다
which starts moving into
1:43
정지 유동으로. 그리고
quiescent flow. And
1:45
이로 인해 이 영역에서 질량 운동이 유발됩니다. 그러므로,
this induces mass motion in this region. So,
1:50
이곳을 영역 2라고 하겠습니다. 그러면
we are call this is region 2, so we have the
1:55
접촉면도 있습니다. 이것이 질량 이동을 일으킵니다. 그 속도를
contact surface also. So, this causes mass motion. So, let us say the velocity of that
2:04
u라고 하고, 이것은
is say u and this is
2:08
분명합니다. 그리고
obviously. And on the
2:13
바깥쪽에는
outside we have an
2:18
이동하는 팽창 팬이 있습니다.
expansion fan which moves
2:21
영역 4로 들어갑니다. 이것이 기본적인 충격관입니다.
into region 4. So, this is the basically the shock tube.
2:24
이제 우리가 집중할 것은 이 법선
Now what we are concentrating is on this normal
2:29
전파하는 충격파입니다. 그럼
shock which is propagating. So, let us do
2:34
그렇게 해 보겠습니다. 이제 여기 이 영역에만 집중해 봅시다.
that. Therefore, now let us just concentrate on this region here.
2:41
충격파가 있습니다. 충격파가
So, we have a shock which we have a shock
2:44
오른쪽으로 이동하고 있습니다.
which is travelling in a trough its right;
2:50
이것은 비정상
this is the unsteady
2:55
이동 충격파입니다.
shock wave travelling.
2:59
이것을 우리가 익숙한
If we have to convert
3:01
정상 상태의 경우로 바꾸려면, 우리가 할 일은
this to the steady state case that we are most familiar with then all we will do is
3:07
이 유동에 이 방향으로
superimpose this flow with a
3:10
속도 W를 중첩하는 것뿐입니다.
velocity W in this direction.
3:17
그렇게 하면
So, if we do that then
3:23
기본적으로 다음과 같은 결과를 얻습니다.
what we get is essentially;
3:29
이제 다시 그려 보면
now sort of redraw
3:34
그렇게 됩니다. 이제 얻는 것은
that. So, what we get now
3:37
이것이 충격파라는 것입니다. 이제 그
is that that this is the shock wave, now the
3:42
속도는 0입니다. 그러므로 속도는
velocity of that is now 0. So, velocity of
3:47
충격파의 속도가 이제 0이므로
the shock wave is now 0, so it
3:52
기본적으로 정지파입니다.
is basically a standing wave
3:58
그리고 속도는
and well then the velocity
4:06
여기서는 가 되고, 이것은
here it becomes and this
4:11
W가 됩니다. 그러므로 여기가 영역
becomes W. So, this is my region
4:15
1이고, 여기가 영역 2입니다. 그러면
1, this is my region 2; so
4:19
이것은 u1이고 이것은 u2입니다.
this is u1 and this is u2.
4:23
그러니까 우리가 한 일은
So, all we have done is taken
4:28
이것을 취해 다른 쪽에 속도 W를 부여한 겁니다
this and imposed a velocity W in the other
4:32
방향으로요. 그러면 속도는 다음과 같습니다
direction. So, what that gives us is a velocity
4:36
여기에는 W, 위쪽에는 W에서 u를 뺀 속도가 있습니다. 그리고
W in here and a velocity W minus up here. And
4:42
이것은 정상파입니다. 정상
this is my steady wave; this is in a steady
4:48
상태의 경우죠. 지난 강의에서 했던 내용입니다.
state case. So, this is what you know we did it in the last lecture.
4:54
그러므로 우리가 한 것은 다음을 써내는 일이었습니다.
So, what we did is we wrote out therefore.
4:59
따라서 w1은 이것이고 u1은 W, u2는
So therefore, w1 is this and u1 is W and u2
Only the first 5 minutes are free. Install the app or extension to keep watching.
DownloadRequest another language





